Used Pumps
Below is a selection of the used equipment we have in stock. Most, if not all, of our stock is in 'as new' condition and we can usually offer warranty. We will test and refurbish as necessary prior to despatch.
Please contact us for prices - no reasonable offer will be refused!
Photos are for illustrative purposes only. If you don't see what you need listed here or you need some modifications, let us know and we will be delighted to help.
Wright Pump TRA10 Model 0150
Drop-in replacement for Waukesha Pump U1 Model 015
- Standard Cover
- Standard Rotors (Twin wing alloy 808 standard clearance)
- Single Mechanical Seal Silicon Carbide Faces and Viton elastomers
- 1.5 inch Triclamp connections
- Stainless steel gear case
Currently coupled to a 0.75kW Leroy Somer motor running at 100 - 456 rpm. This pump and motor combination will pump 5.5 - 25 litres per minute. Pump and motor mounted on a 304 Stainless Steel Baseplate.
Waukesha Pump Universal 1 Model 60
Upgraded from Waukesha Pump specification to Wright Pump standards.
- Standard Cover
- Standard Rotors (Twin wing alloy 808 standard clearance)
- Seal to be specified by buyer and dependant on the application
- 2.5 inch ISS connections
- Standard gear case
Bareshaft pump only but depending on your needs, we can supply a suitable motor from a range of recognised manufacturers. We can also mount onto customised baseplate constructed from Stainless Steel if required.
Wright Pump TRA10 Model 0450
There is no drop-in Waukesha Pump equivalent for this model
- Standard Cover
- Standard Rotors (Twin wing alloy 808 standard clearance)
- Single Mechanical Seal Silicon Carbide Faces and Viton elastomers
- 2 inch RJT connections
- Standard gear case
Currently coupled to a 1.1kW Leroy Somer motor running at 10 - 119 rpm. This pump and motor combination will pump 4 - 50 litres per minute. Pump and motor mounted on a 304 Stainless Steel Baseplate.
Fristam FL2 130L Rotary Lobe Pump
- Standard Cover
- Standard Rotors
- Single Mechanical Seal with Carbon versus Stainless Steel faces and Viton elastomers
- 4 inch RJT connections
- Bottom drive shaft
- 2.45 litres per revolution
Bareshaft pump - we can supply motor and baseplate if required. Flow rates up to 60m³/Hr. Discharge pressure up to 120 PSI / 8 BAR. Pump in very good condition and has only been run for a maximum of 6 months. Today's list price is in the region of £9000 GBP but we welcome reasonable offers!
Cesco Magnetics Magtrap Model 125 4 inch
- Male screwed connections
Powerful rare-earth magnets to capture and hold ferrous or work-hardened trash from nuts and bolts to stainless steel fines as small as 0.0001 inches in diameter from process and transfer lines. Machined from solid or low magnetic permeability centrifugally cast 316 Stainless Steel with food grade gaskets.
Used when processing fragile solids such as fruit preserves, cooked meats, cottage cheese, or sinewy products where they are placed in front of pumps, screens, or mills to protect equipment from damage, or in front of fillers to ensure product quality.
Cesco Magnetics Magtrap Model 125 2 inch
- Weld end connections
Powerful rare-earth magnets to capture and hold ferrous or work-hardened trash from nuts and bolts to stainless steel fines as small as 0.0001 inches in diameter from process and transfer lines. Machined from solid or low magnetic permeability centrifugally cast 316 Stainless Steel with food grade gaskets.
Used when processing fragile solids such as fruit preserves, cooked meats, cottage cheese, or sinewy products where they are placed in front of pumps, screens, or mills to protect equipment from damage, or in front of fillers to ensure product quality.